Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
| qcsmarine:mercuryservicechecklist [2021/01/16 21:41] – admin | qcsmarine:mercuryservicechecklist [2021/01/16 22:00] (current) – admin | ||
|---|---|---|---|
| Line 5: | Line 5: | ||
| === 60 MONTHS / 500 HOURS (WHICHEVER OCCURS FIRST) SERVICE CHECKUP === | === 60 MONTHS / 500 HOURS (WHICHEVER OCCURS FIRST) SERVICE CHECKUP === | ||
| + | <WRAP left round box 60%> | ||
| + | === Outboard === | ||
| + | \\ | ||
| + | [[http:// | ||
| + | \\ | ||
| + | === Check Before running === | ||
| + | Inspect outboard motor and accessories for visible damage\\ | ||
| + | Drain gear housing and refill with gear lube\\ | ||
| + | Lubricate all grease fittings, transom clamp screws, throttle/ | ||
| + | Lubricate steering cable. Clean and lubricate cable end at engine\\ | ||
| + | Service water pump\\ | ||
| + | Remove and inspect propeller. Grease propeller shaft spline\\ | ||
| + | Torque propeller shaft nut to specification\\ | ||
| + | Check all electrical connections. Clean and reseal, if required\\ | ||
| + | Service battery and terminals\\ | ||
| + | Remove and inspect spark plugs, protectors and leads.Check compression (engine must be warm)\\ | ||
| + | Remove engine deposits with Quicksilver Power Tune Engine Cleaner\\ | ||
| + | Inspect fuel tank, fuel lines and connections\\ | ||
| + | Replace fuel filters and oil injection filter\\ | ||
| + | Replace fuel pump diaphragm and check carburetor float levels\\ | ||
| + | Check carburetor throttle butterfly synchronization\\ | ||
| + | Check primary and secondary throttle pick ups and full throttle stop\\ | ||
| + | Check oil level and operation of power trim system and power trim gauge\\ | ||
| + | Check Thermostat and Poppet valve\\ | ||
| + | \\ | ||
| + | === EFI and DFI === | ||
| + | Check T.P.S. settings\\ | ||
| + | \\ | ||
| + | === 4 stroke only === | ||
| + | Change engine oil and replace oil filter\\ | ||
| + | Check and adjust valve clearance, if necessary inspect timing belt\\ | ||
| + | \\ | ||
| + | === Check While running === | ||
| + | |||
| + | Water pressure \\ | ||
| + | Operation of water pump, cooling system and thermostat\\ | ||
| + | Throttle, gearshift and reverse lock operation\\ | ||
| + | Alternator is charging\\ | ||
| + | Carburettor mixture and idle speed\\ | ||
| + | Operation of oil injection and low oil warning system\\ | ||
| + | Operation of steering system, remote controls and gauges\\ | ||
| + | \\ | ||
| + | === Optimax and EFI models === | ||
| + | Use CDS to check engine operation\\ | ||
| + | Check diagnostic codes\\ | ||
| + | ECM and sensor operation\\ | ||
| + | \\ | ||
| + | === Important === | ||
| + | Spray powerhead with Quicksilver Corrosion Guard to protect electrical connections and exposed metal surfaces from corrosion | ||
| + | Inspect corrosion control anodes and system. Replace trim tab if required | ||
| + | Owner should follow recommendations in Operation and Maintenance Manual until next scheduled service | ||
| + | Additional items maybe required depending on usage and /or application | ||
| + | \\ | ||
| + | </ | ||
| + | |||
| + | |||
| + | <WRAP left round box 60%> | ||
| + | === Inboard === | ||
| \\ | \\ | ||
| **IB** = Inboard | **IB** = Inboard | ||
| Line 66: | Line 124: | ||
| Audio warning system operation (ISE)Preparation for Storage | Audio warning system operation (ISE)Preparation for Storage | ||
| Extended storage procedure completedIB = Inboard | Extended storage procedure completedIB = Inboard | ||
| + | |||
| + | </ | ||
| + | |||